Call 08048600099 66% Response Rate

Send Enquiry

our range

Parker Sae Hydraulic Flange Distributors

Parker offers flanges that accommodate every configuration and substrate. Parker flanges meet or exceed all industry standards and specifications, and only we can provide the most efficient and appropriate flange for every hose or tube product.

The Parker 4-bolt flange connections conform to SAE J518 and ISO 6162-1 and -2. Flanges are proven leak-free connections especially suited for larger sizes, higher pressures, and assembly in tight quarters.

Threaded port connections, such as SAE straight thread O-ring and ISO 6149, are easy to assemble and provide 6000 psi (and higher) pressure capability up to size 3/4” and 27mm (beyond 3/4” size the pressure rating decreases and assembly torques increase).

Compared to an equivalent size, threaded port Parker 4-bolt flange connections require lower assembly torque; another advantage in tight quarters where wrench clearances are limited.

All Parker flange fittings (except for those with square mounting hole patterns – nomenclature code QS), are designed to conform to O-ring groove, bolt holes and bolt pattern dimensions of either Code 61 or Code 62 of SAE J518 and ISO 6162-1 (Code 61) or -2 (Code 62).

The flange adapters (Code Q1 and Q2), and flange block fittings (Codes Q1B, Q2B and QSB) have O-ring grooves conforming to dimensions in SAE J518. The flange block fittings (Codes Q1B and Q2B) have through holes for the mounting bolts conforming to SAE J518.

 

There is no industry standard for the bolt pattern of the square pattern block flanges with codes QSP and QSB. The flange pad fittings (Codes Q1P, Q2P, and QSP) have a flat face (no O-ring groove) and the mounting holes are tapped. Where these fittings are used, the seal is in the mating part (flange adapter, flange hose fitting, flange block fitting, etc.)

Parker flange clamps are forged for higher strength and durability. They meet all requirements of SAE J518. The split clamps make it easy to assemble the connection in close quarters. They also make removal of the flange head component, such as a hose assembly, easy by loosening all four bolts and removing one clamp half, 

Parker Hydraulic SAE Non Weldable Flange

Parker Hydraulic SAE Non Weldable Flange

Rs 9,500  / PieceGet Best Price
Flange Face TypeWeld Neck
Size5-10 inch
MaterialStainless Steel
ApplicationIndustrial
TechnicsForged Casting

Weld nozzle flanges are designed with butt weld type to weld the pipe on both the side to the attached nozzle. weld nozzle flanges are consists of set of split flanges assembled with weld nozzle both side with o ring , allen bolts & nuts. weld nozzle flanges are easy for assembled, weld & ease of removal during assembly or disassembly of piping joints.
Sae weld nozzle flanges are used for bigger sizes of joints in the piping conncetion where nut & ferrule asembly is not possible. sae weld nozzle flanges are in moc - steel , stainless steel sae weld nozzle flanges are assembled with split flanges or mono flanges or flat socket type flanges with weld nozzle on both side having o ring seal groove.
sae weld nozzle flanges are designed as per iso 6162 with static pressure for 3000 psi & 6000 psi series. 

View Complete details

get quote request a call back
Parker SAE Flange

Parker SAE Flange

Rs 1,250  / PieceGet Best Price

Minimum Order Quantity: 25 Piece

MaterialCarbon Steel
BrandParker
Packaging TypeBox
No. Of Holes4
Size1/2-48 inch
Parker offers 1-piece full or 2-piece flange kits, and single or double block and bleed flange connections.


Flanges by Parker are Designed to:

  • Provide different methods of connecting a tube, hose, pipe or other fittings to standard ports
  • Replace weld fittings
  • Interface with pressure measuring systems

Hydraulic Flanges are connection between hoses or seamless tubes where easy removal is required with in close quarters in the piping systems. Hydraulic Flanges are mainly used for Bigger sizes of tubes in NB ( Nominal Bore ) sizes. Hydraulic Flanges are used in bigger sizes of Piping joints Where Nut & ferrule assembly is not possible due to higher in Hex section sizes & High torgue require to tighetened / Grip the ferrule in to the tube & lead to loose the joints at High pressure application. In such cases the usage of Flanges with Butt weld or Socket weld has been found to be more practical leading to compact piping installation. Further , the orientation of Hydraulic Flanges joints can be so done to minimize the distance between pipes and provide for a compact installation. CETOP Flanges and ISO 6164 Specify Flanges with Butt weld ends and Square clamping Flanges for 250 bar and 400 bas static working Pressure respectively. These correspond to 160 bar and 315 Bar dynamic Working Pressures. The Flange System consist of a Sleeve to be Butt or Socket Welded to the Pipe and clamped together betwwen two square Flanges by a set of four Hex bolts , Nuts and Spring washers, One of the sleeves carries an O ring groove fitted with an O ring for sealing the interface.


The use of ISO 6164 Flanges has one disadvantage , The size of the Square Flange require a higher pitch between pipes due to the Flange Sizes. In order to reduce the distance between pipes , SAE introduced their own Standards which are now incorporated in to ISO 6162 for the 3000 psi and 6000 psi static Pressure ranges respectivelty. SAE system depends on the same set of butt welding sleeves held together by a set of Split Flange and Solid Flange secured by Hex Bolts and Nut. 

Hydarulic Flanges Standard W.P = PSI .SERIES SIZES IN NB SIZES IN OD IN MM CLICK to Submit
SAE Flanges ISO 61 ISO 62 3000 6000 1/4' NB UP TO 5'NB 15 MM OD UP 140 MM OD Enquiry Form
CETO Flanges CETOP RP 63H 3000 6000 1/4' NB UP TO 5'NB 15 MM OD UP 140 MM OD Enquiry Form
4 Bolt Square Flanges ISO/ DIS 6164 3000 6000 1/4' NB UP TO 5'NB 1/4' NB UP TO 5'NB Enquiry Form

View Complete details

get quote request a call back
Parker Sae Female Threads Flanges

Parker Sae Female Threads Flanges

Rs 1,550  / PieceGet Best Price

Minimum Order Quantity: 25 Piece

MaterialStainless Steel
Usage/ApplicationIndustrial
Size1-5 inch
Number Of Hole4
Head ShapeRound
Pressure3000 PSI & 6000 PSI
Parker offered thread flanges are designed as per iso 6162 - 3000 psi series & 6000 psi series only. thread flanges are used for hose assembly where easy removal piping can be possible with in close area thread flanges are in 2 halves attached with weld nozzle with allen bolts , nuts & o ring seal. sae thread flanges are in moc - steel , stainless steel sae thread flanges are assembled with split flanges or mono flanges or flat butt type flanges with tube to weld on both side with allen bolts & nuts. sae thread flanges are designed as per iso 6162 with static pressure for 3000 psi & 6000 psi series. sizes available - 1/4 " nb up to 5 " nb

View Complete details

get quote request a call back
Parker Split Flange

Parker Split Flange

Rs 750  / PieceGet Best Price

Minimum Order Quantity: 25 Piece

Size0-1 inch, 1-5 inch
MaterialCarbon steel
ApplicationHydraulic Hose Fitting
UsageSpare Parts
Parker offers 1-piece full or 2-piece flange kits, and single or double block and bleed flange connections.


Flanges by Parker are designed to:

  • Provide different methods of connecting a tube, hose, pipe or other fittings to standard ports
  • Replace weld fittings
  • Interface with pressure measuring systems

Split Flanges are designed as per ISO 6162 - 3000 psi series & 6000 Psi Series only. Split Flanges are used for Hose assembly where easy removal piping can be possible with in close area Split Flanges are in 2 halves attached with Weld nozzle with Allen bolts , Nuts & O ring Seal. SAE Split Flanges are in MOC - Steel , Stainless Steel SAE Split Flanges are assembled with Weld Nozzles or Mono Flanges or Flat Socket type flanges with Weld Nozzle on both side having O ring Seal groove. 

View Complete details

get quote request a call back

EXPLORE MORE CATEGORIES